RESITRIX® SK Partial Bond two rolles

RESITRIX® SK Partial Bond EPDM roofing membrane

Partially self-adhesive 3-in-1 waterproof membrane

RESITRIX® SK Partial Bond is a hot air-weldable waterproofing membrane with a synthetic rubber (EPDM) base.

RESITRIX® SKP is the first partially self-adhesive 3-in-1 waterproofing membrane. It combines a waterproofing section, a vapour pressure equalisation section and a movement compensation section in a single layer.

These special properties are particularly beneficial for use on materials prone to a great deal of movement and substrates with trapped residual moisture. This also makes RESITRIX® SK Partial Bond a perfect choice for partial surface and complete refurbishment projects.

  • Certified service life of more than 50 years and also named the only product of its kind for joining seams (according to a study conducted by the German Plastics Centre)
  • Simple and safe installation without any need for naked flames
  • 100% leak-tight welded seam with a simple visual inspection
  • Sustainable (EPD certified and DGNB compliant)

RESITRIX® SK PARTIAL BOND references

Research Station Gondwana, Antarctic

Zukunftshaus, Bottrop, DE

Tips and tricks for installing RESITRIX®

Material benefits:

  • No additional surface protection; permanently resistant to ozone, UV radiation and infrared radiation
  • Single-layer waterproofing
  • Permanently elastic and flexible
  • Ultimate elongation of more than 500%
  • Practically free from shrinkage throughout its entire service life
  • Permanently elastic and flexible at low temperatures of down to -40°C
  • Resistant to micro-organisms
  • Capable of withstanding a multitude of chemical substances and environmental emissions
  • 100% bitumen-resistant
  • Free from plasticisers and chlorine
  • No shattering effect
  • Environmentally friendly and recyclable

Installation related benefits:

  • Simple and safe Installation without any need for naked flames
  • 100% leak-tight welded seam – simple visual inspection
  • Partially self-adhesive system
  • The entire underside of the EPDM membrane can be welded
  • Non-slip surface, even when wet
  • No additional measures required for the T-joint area
  • Can be welded with hot air down to -10°C

RESITRIX® SK Partial Bond is a hot air-weldable waterproofing membrane with a synthetic rubber (EPDM) base and a glass fabric liner. The underside has a partially self-adhesive, polymer-modified layer of bitumen that is protected by a detachable release film.

  • Thickness of the EPDM layer: 1.6 mm
  • Total membrane thickness: 2.5 mm
  • Surface weight: Approx. 2.75 kg/m²
  • Standard delivery length per roll: 10 m
  • Standard delivery width: 1 m (strips upon request)
  • Membrane designation acc. to DIN SPEC 20000-201: DE/E1 EPDM-BV-V-GG-1.6-SK
  • Membrane designation acc. to DIN SPEC 20000-202: BA/MSB-nQ EPDM-BV-V-GG-1.6-SK
  • CE certification acc. to DIN EN 13956 and DIN EN 13967
  • Satisfies the requirements acc. to DIN 18531, the specialist regulations for waterproofing systems (Flat Roof Guidelines) acc. to DIN 18532, DIN 18533, DIN 18534 and DIN 18535

The following Installation variants are possible:

  • Partial self-adhesion on full-surface primer
  • Partial self-adhesion without primer (on exposed or fresh bitumen substrate only)
+ Product benefits

Material benefits:

  • No additional surface protection; permanently resistant to ozone, UV radiation and infrared radiation
  • Single-layer waterproofing
  • Permanently elastic and flexible
  • Ultimate elongation of more than 500%
  • Practically free from shrinkage throughout its entire service life
  • Permanently elastic and flexible at low temperatures of down to -40°C
  • Resistant to micro-organisms
  • Capable of withstanding a multitude of chemical substances and environmental emissions
  • 100% bitumen-resistant
  • Free from plasticisers and chlorine
  • No shattering effect
  • Environmentally friendly and recyclable

Installation related benefits:

  • Simple and safe Installation without any need for naked flames
  • 100% leak-tight welded seam – simple visual inspection
  • Partially self-adhesive system
  • The entire underside of the EPDM membrane can be welded
  • Non-slip surface, even when wet
  • No additional measures required for the T-joint area
  • Can be welded with hot air down to -10°C
+ Product properties

RESITRIX® SK Partial Bond is a hot air-weldable waterproofing membrane with a synthetic rubber (EPDM) base and a glass fabric liner. The underside has a partially self-adhesive, polymer-modified layer of bitumen that is protected by a detachable release film.

  • Thickness of the EPDM layer: 1.6 mm
  • Total membrane thickness: 2.5 mm
  • Surface weight: Approx. 2.75 kg/m²
  • Standard delivery length per roll: 10 m
  • Standard delivery width: 1 m (strips upon request)
  • Membrane designation acc. to DIN SPEC 20000-201: DE/E1 EPDM-BV-V-GG-1.6-SK
  • Membrane designation acc. to DIN SPEC 20000-202: BA/MSB-nQ EPDM-BV-V-GG-1.6-SK
  • CE certification acc. to DIN EN 13956 and DIN EN 13967
  • Satisfies the requirements acc. to DIN 18531, the specialist regulations for waterproofing systems (Flat Roof Guidelines) acc. to DIN 18532, DIN 18533, DIN 18534 and DIN 18535
+ Installation variants

The following Installation variants are possible:

  • Partial self-adhesion on full-surface primer
  • Partial self-adhesion without primer (on exposed or fresh bitumen substrate only)

Downloads for system accessories

RESITRIX® SK Datasheet

RESITRIX® Product Catalogue

RESITRIX® Installation Instructions

RESITRIX® Specification Guidlines

RESITRIX® Specification Guidlines

Suitable RESITRIX® accessories